Do you need a physics degree to climb? No, but understanding the forces involved in climbing is very important.
Here is the short answer. Force is measured in kilonewtons (kN), and a 100 kg climber hanging still on a rope puts about 1 kN through it. A fall puts in a lot more, and the best single guide to how much more is the climbing fall factor, which is the length of the fall divided by the amount of rope paid out. Keep the fall factor low and your body and your kit both have an easier time.
Knowing this helps you understand your kit, read the instructions that come with it and know when to retire it. It also makes sense of the kN figures all through this gear guide.
The video below is our own, made for the original version of this guide in 2012. Where its figures differ from the tables further down, go with the tables, which are checked against today’s makers and standards.
What is a kilonewton?
Force is measured in newtons, or for the larger forces we get in climbing, kilonewtons (kN). One kilonewton is 1,000 newtons.
So if a climber has a mass of 100 kg (just under 16 stone), that climber hanging on a rope pulls on it with about 1 kN, just through the earth’s gravity. Strictly it is 0.98 kN, but rounding it keeps the sums easy. 1 kN is roughly the weight of 100 kg.
The moment the climber moves, bounces or falls, the force goes up. Their mass has not changed, but the force on the rope and the anchor has.
A top rope fall stays gentle if the belayer keeps the slack in. Petzl says that when a second falls with no slack in the rope above them, the impact force is very low, about the same as hanging.
These forces are not that great in the world of climbing. The more important thing is the fall factor.
What is the climbing fall factor?
The fall factor is a number you can work out to show how severe a fall is, and so how much force it puts on you and your equipment. The higher the number, the harder the catch.
It is the length of the fall divided by the rope paid out, meaning the rope between the belayer and the climber. The sum (don’t worry, it’s not that bad!) looks like this.
Fall factor = length of fall ÷ rope paid out
In normal roped climbing, the maximum a fall factor can ever be is 2. Petzl and the BMC both define it this way, and Petzl gives the range in climbing as 0 to 2.
How do you work out a fall factor?
So if you fell 10 metres onto 10 metres of rope, your fall factor would be 1. That is still a pretty high fall factor. The BMC calls a fall of around factor 1 or more a serious fall, and says a rope that has held one should be considered for downgrading, meaning no longer used for leading.
A fall of 20 metres onto 10 metres of rope, falling down past the belayer, gives a fall factor of 2. This is the maximum you should be able to get in a climbing environment, and it is very serious. Petzl says a lead fall puts the highest loads on a belay anchor, and higher still at the start of a pitch, with little rope out.
The diagrams below show four falls, from factor 0.57 up to the maximum of 2. They are drawn in feet, and the sum works the same in metres.




The fall factor does not tell you what you might hit, though. The BMC points out that where the danger is a ledge or the ground, the length of the fall matters more. Our guide to how to fall safely when climbing covers that side of it.
Why is a real fall different from the sums?
The sum does not allow for friction (the rope rubbing on karabiners and rock), or for what the belayer does. It can be worked out, but not easily.
Friction makes it worse. The BMC and Petzl both explain that when the rope drags through runners and over rock, only the rope nearest the climber can stretch, so the effective fall factor goes up. The climber gets more of a jolt and the top runner takes more load.
The belayer can make it better. Petzl found that letting the belayer move soaks up a big part of the energy. Rope slipping through the belay device helps too, but the BMC advises against allowing it on purpose, as it can burn your hand and you may lose control of the rope.
How can you reduce the fall factor?
The most important way is placing runners (bits of gear in the rock). A runner above the belay shortens the fall you can take for the rope you have out, so the fall factor drops below 2.
Even as soon as you leave a stance (a ledge partway up a cliff where the belayer stands), you should place a bit of gear to stop the fall factor being 2. At the very least, clip the rope through a bit of bomber (very good) gear on the stance itself. Petzl agrees that the first point after the belay must be solid, and suggests a quickdraw on the top anchor point for the leader to clip first.
Another way to cut the force is dynamic belaying, where the belayer gives a softer catch so the climber stops more slowly. Strictly it changes how hard the catch is, not the fall factor. Our guide to how to lead belay covers the soft catch.
This matters because if you understand fall factors, you can keep them low using the techniques above, and so help prevent gear failure and injury.
Clip something solid as soon as you leave a stance
The hardest fall in roped climbing is a factor 2, when a leader falls past the belay with no gear in. Place a solid runner as soon as you leave a stance, or at the very least clip the rope through a bomber piece on the stance before you set off.
This guide is about understanding forces and kit, not about using it. Placing gear, building belays and belaying a leader are learned in person from a qualified instructor or at your climbing wall, not from an article.
What forces do real falls produce?
Most kN figures quoted online come from lab tests with a metal weight falling onto a fixed point, which Petzl says gives high values. So it measured falls with real people.
| The fall | Fall factor | Climber | Belayer | Top runner |
|---|---|---|---|---|
| 2 m on 6.9 m of rope, belayer on the ground | 0.3 | 2.5 kN | 1.5 kN | 4 kN |
| 2 m on 3 m of rope, start of a multi-pitch | 0.7 | 3 kN | 2 kN | 5 kN |
| 3.6 m on 3.6 m of rope, leaving a belay | 1 | 4 kN | 2 kN | 6 kN |
So falls up to factor 1 put about 2.5 to 4 kN on the climber, and Petzl says even the factor 1 force is quite bearable.
Look at the last column, though. The top runner took more than the climber every time, roughly the climber’s and the belayer’s figures added together. Petzl calls this the pulley effect, and notes that 6 kN is no problem for a solid fixed anchor but would be critical on a small wire or a bad peg.
We found no real-world figures for bigger falls, so we will not guess. Petzl’s full write-up is forces at work in a real fall.
What does the 12 kN on a rope label mean?
You will often see 12 kN quoted as the most force a dynamic rope can ever put on you. That is not quite right.
12 kN is the limit in the standard drop test for ropes, EN 892. An 80 kg metal mass falls at a fall factor of 1.77 onto a rope tied to a fixed point, and a new single rope must not transmit more than 12 kN on the first drop. Half ropes are tested with 55 kg and a limit of 8 kN. The BMC calls the test a very severe fall, and Petzl says it does not represent a real climbing fall.
So the standard makes manufacturers design ropes that stretch enough to soften the shock. But 12 kN is a test result for a new rope, not a ceiling. The BMC notes that a rope’s impact force rises with use, and the test mass is 80 kg, so a heavier climber can expect a bit more. Our ropes guide and the BMC’s guide to ropes have more.
What forces can your gear take?
Here is how strong typical climbing kit is, against the European standard’s minimum. Always check the manufacturer’s figures for your own kit. The standards for karabiners, slings, nuts and cams require the strength to be marked on the product.
| Kit | Current ratings | Standard minimum |
|---|---|---|
| Sewn Dyneema sling | 22 kN (DMM Dynatec) | 22 kN (EN 566) |
| Karabiner, gate closed | 24 kN (Black Diamond HotWire), 25 kN (DMM Alpha Wire) | 20 kN (EN 12275) |
| Karabiner, gate open | 8 kN (HotWire), 9 kN (Alpha Wire) | 7 kN |
| Karabiner, loaded across its width | 8 kN (HotWire), 9 kN (Alpha Wire) | 7 kN |
| Micro nut | 2 to 6 kN (DMM Micro Wallnuts) | 2 kN (EN 12270) |
| Small nut | 7 kN (DMM Wallnut 1) | 2 kN |
| Mid-size nut | 10 kN (Black Diamond Stopper 9), 12 kN (DMM Wallnut 9) | 2 kN |
| Cam | 10 to 14 kN (DMM Dragon, sizes 00 to 8) | 5 kN (EN 12276) |
| Micro cam | 5 to 6 kN (smallest three Camalot Z4s), 6 to 9 kN (DMM Dragonfly) | 5 kN |
| Sit harness | Belay loop must hold 15 kN for 3 minutes in CE testing (Black Diamond) | 15 kN up, then 10 kN down (EN 12277) |
Nut sizes differ between makers (a Black Diamond Stopper 1 is a 2 kN micro size), and a rating is the strength of the piece in a test rig, not of your placement. Our nuts, hexes and cams guide covers the gear itself.
The karabiner rows are the ones to remember. A karabiner is far weaker with the gate open or loaded across its width. The UIAA says an open gate roughly divides the strength by three, and gates can flick open for a moment in a fall. The BMC’s karabiner guidance, published by the UIAA, suggests 8 or 9 kN gate-open karabiners if you are heavier or carry a lot of gear.
Now put the two tables together. Petzl’s falls up to factor 1 put 4 to 6 kN on the top runner. So apart from the micro gear, every piece in the table is rated above that, most of them comfortably. With micro gear the margin is thin or gone, which is Petzl’s point about small wires.
Where this sits in the gear guide
- Climbing shoes and harnesses are the first two things most beginners buy, and the harness guide explains its 15 kN test.
- Belay devices are where the belayer’s side of every fall ends up.
- Ropes covers impact force, rope types and when a hard fall means retiring a rope.
- Slings and webbing covers the 22 kN slings in the table above.
- Protection covers the nuts, hexes and cams whose ratings you have just read.
- The BMC helmet guide covers the other piece of kit you will want on a crag.
Frequently Asked Questions
What is a fall factor in climbing?
The length of a fall divided by the rope paid out between the belayer and the climber. In normal roped climbing it runs from 0 to 2, and the higher it is, the harder the catch on you and your gear.
What is the worst fall factor in climbing?
A fall factor of 2, when a leader with no gear in falls past the belay. Avoid it by placing a solid runner as soon as you leave a stance, or at least clipping the rope through a bomber piece on the stance.
How many kN does a climbing fall generate?
In Petzl’s tests with an 80 kg climber, falls from factor 0.3 to 1 put about 2.5 to 4 kN on the climber and 4 to 6 kN on the top runner. Rope drag pushes those figures up.
Is 12 kN the most force a climbing rope can produce?
No. It is the most a new single rope may transmit in the standard drop test, an 80 kg metal mass falling at factor 1.77 onto a fixed point. A rope’s impact force rises with use, and a heavier climber puts more into the system.
How strong is a climbing karabiner?
The European standard asks a basic karabiner to hold at least 20 kN with the gate closed, and 7 kN with the gate open or loaded across its width. The Black Diamond and DMM models we checked are rated 24 and 25 kN closed but only 8 and 9 kN open.
In short
Force is measured in kN, and the climbing fall factor, never more than 2 in normal roped climbing, is your best guide to how hard a fall is on you and your kit, so it pays to know what your gear can do and how to keep the force on it down.
Next time you are on a multi-pitch route, work out the fall factor at the start of each pitch and place something solid as soon as you leave the stance. Then how to lead belay is the next step.
Ask any questions in the comments below.




